★ Free US shipping over $99Real stock, ships next business dayVoron · ERCF · Ender · Milo · Stinger · Printers for AntsThe Sale is on — real markdowns, honest pricesdfh.fm — for makers

Machines

Sort by

▾

↑ Load previous

BIGTREETECH TMC2209 v1.2 StepStick stepper driver module with heatsink for 3D printer control boards

3D Printer Electronics > Stepper Driver

BTT TMC2209 v1.2 Stepper Driver

Black EPDM rubber printer foot with recessed washer and center mounting hole

3D Printer Accessories > Rubber Feet

EPDM Rubber Feet - Set of 4

Molex Micro-Fit 3.0 dual-row 4-circuit connector kit with black housings and crimp terminals

3D Printer Parts > Electrical > Wire Connectors

Molex Micro-Fit Dual Row 4 Circuit Kit

Longs 36HS2418CL16 round NEMA14 pancake stepper motor with 10-tooth gear and 4-wire connector

3D Printer Parts > Motion > Stepper Motors

Longs Nema14 Stepper Motor

695-2RS sealed miniature ball bearing with black rubber seals, 5x13x4mm non-flanged bearing

695-2RS Bearings

Black SKR Mini E3 thermistor expander PCB with two white JST-XH thermistor sockets, 5-pin TFT header, and 3.3V jumper pin.

3D Printer Electronics > Thermistor Expansion Board

SKR Mini E3 V2.0 Thermistor Expander by Timmit99

Voron V0.1 belted Z kit hardware with GT2 belt, 20T pulleys, bearings, shaft, washers, nuts, inserts, and fasteners

3D Printer Parts > Motion Kits

Voron V0 Belted Z Kit

FYSETC Voron V0_Display 1.3 inch OLED controller PCB with rotary encoder, reset/kill buttons, USB port, GPIO header, and onboard Neopixel

3D Printer Parts > Electronics > Displays

Voron v0 Display

Klicky Probe hardware kit with microswitch, 6x3 magnets, screws, threaded inserts and T-nuts for Voron magnetic Z probe

3D Printer Probe Kit

Klicky Probe Kit

TCRT5000 reflective optical sensor module on a small breakout PCB, top-down view: 4-pin header (Vcc, GND, DO, AO), IR LED + phototransistor package, sensitivity trimpot, two 3 mm mounting holes.

Reflective Optical Sensor

TCRT5000 Sensor

Molex 43045-1400 black Micro-Fit 3.0 14-circuit right-angle PCB header connector

3D Printer Parts > Electrical > Wire Connectors

Molex 43045-1400 Micro-Fit 3.0 14-Pin 14-Way Female Header Connector

Black Voron V0.1 umbilical frame and toolhead PCBs with JST-XH headers, 14-pin Micro-Fit connector, and blue screw terminal

3D Printer Parts > Electronics > Toolhead PCB

Voron v0 Umbillical and Rear Connector Boards Pack

Black and clear slim nylon zip ties for Voron cable management, 2mm wide, 40 pack

3D Printer Parts > Cable Management > Zip Ties

Voron Slim Zip-Tie Kit

Black nylon 4 inch and 12 inch zip ties for Voron cable routing and wiring cleanup

3D Printer Parts > Cable Management > Zip Ties

Voron Zip Tie Kit

WAGO 221-415 5-conductor COMPACT splicing connector, transparent housing, five orange side-entry levers on a 4 mm² / 24-12 AWG body.

3D Printer Parts > Electrical > Wire Connectors

Wago 221-415

WAGO 221-413 3-conductor COMPACT splicing connector with transparent housing, three orange side-entry levers, and 4 mm² / 24-12 AWG body.

3D Printer Parts > Electrical > Wire Connectors

Wago 221-413

Slim 24V 40W hotend heater cartridge with red braided leads and metal cartridge body

3D Printer Parts > Hotend Heater Cartridge

Slim Heater Cartridge 24v 40w

Enraged Rabbit Carrot Patch ERCP hardware kit with fasteners, 608ZZ bearing, ECAS04 collet and PTFE fittings

3D Printer Parts > ERCF Hardware Kits

Enraged Rabbit Carrot Patch

Gates 188-2GT-6 RF black closed-loop GT2 timing belt, 188 mm loop length and 6 mm width

Gates 188-2GT-6 RF Closed Loop Belt

Transparent FEP filament feed tube coil, 2.5 mm ID x 4 mm OD, for ERCF and Bowden-style filament paths

Transparent FEP Tube

~~$9.99~~

Blue ADXL345 3-axis accelerometer breakout board with loose male pin header for SPI or I2C wiring

3D Printer Electronics > Accelerometer

ADXL345 Accelerometer

Orange plastic collet retaining clips for 4 mm PTFE Bowden push-fit couplers

3D Printer Parts > Bowden Tube Collet Clips

Collet Clip

Stainless steel MakerBeamXL M3 T-slot nut for 15x15 aluminum extrusion

3D Printer Parts > Fasteners > T-Slot Nuts

Makerbeam XL T-Nut

Pile of small 3x5x7mm BMG-style needle roller bearings for 3mm extruder drive gear shafts

3D Printer Parts > Extruder Hardware

BMG Style Needle Bearings