Voron

Sort by

▾

↑ Load previous

Omron Z-15GS-B Z-series slim spring plunger limit switch with screw terminals

3D Printer Parts > Electronics > Microswitches

Omron Z-15GS-B Z Limit Switch

Red insulated #6 fork spade crimp terminals for 22–18 AWG wire, sold as a 10-pack

3D Printer Parts > Wiring & Electrical > Wire Terminals

Insulated Fork Spade Terminal

ERCF toolhead sensor kit with AH3364Q-P-B Hall sensor, JST-XH 3-pin housing and pins, steel washer, and round magnet

3D Printer Parts > ERCF Sensor Kit

Enraged Rabbit Carrot Feeder Toolhead Sensor Kit

Runice 20T toothed GT2 idler pulley, 5mm bore and 9mm belt width, silver aluminum with flanges

3D Printer Parts > Motion > Idlers

20T Idler Bore 5mm Width 9mm by Runice

Silver Runice 20T toothed GT2 idler pulley with 5 mm bore for 6 mm timing belt

Timing Idler Pulley

20T Idler Bore 5mm Width 6mm by Runice

Silver Runice RLA16-2GT-6-C-P5-H15.5 16T GT2 timing pulley with flanges for 5 mm bore and 6 mm belt

Silver 16T Pulley Bore 5mm Width 6mm by Runice

Silver Runice RLA20-2GT-6-C-P5-H16 20T GT2 timing pulley with 5 mm bore for 6 mm belts

20T Pulley Bore 5mm Width 6mm by Runice

Black Phaetus Dragonfly BMO all-metal V6 hotend with copper alloy heat block, heatsink, and plated nozzle

3D Printer Parts > Hotends

Phaetus Dragonfly BMO

Lightweight Labware titanium extrusion backers with countersunk mounting holes for Voron V2.4 and Trident gantry rails

3D Printer Parts > Gantry Backers

Titanium Extrusion Backers - by Lightweight Labware

Runice BMG-style extruder component kit with drive gears, shafts, bearings, tension screw, washer, nut, and retaining clips

3D Printer Parts > Extruder Hardware

Extruder Components Kit by Runice

BIGTREETECH TMC2209 v1.2 StepStick stepper driver module with heatsink for 3D printer control boards

3D Printer Electronics > Stepper Driver

BTT TMC2209 v1.2 Stepper Driver

Black EPDM rubber printer foot with recessed washer and center mounting hole

3D Printer Accessories > Rubber Feet

EPDM Rubber Feet - Set of 4

Molex Micro-Fit 3.0 dual-row 4-circuit connector kit with black housings and crimp terminals

3D Printer Parts > Electrical > Wire Connectors

Molex Micro-Fit Dual Row 4 Circuit Kit

Longs 36HS2418CL16 round NEMA14 pancake stepper motor with 10-tooth gear and 4-wire connector

3D Printer Parts > Motion > Stepper Motors

Longs Nema14 Stepper Motor

695-2RS sealed miniature ball bearing with black rubber seals, 5x13x4mm non-flanged bearing

695-2RS Bearings

Black SKR Mini E3 thermistor expander PCB with two white JST-XH thermistor sockets, 5-pin TFT header, and 3.3V jumper pin.

3D Printer Electronics > Thermistor Expansion Board

SKR Mini E3 V2.0 Thermistor Expander by Timmit99

Voron V0.1 belted Z kit hardware with GT2 belt, 20T pulleys, bearings, shaft, washers, nuts, inserts, and fasteners

3D Printer Parts > Motion Kits

Voron V0 Belted Z Kit

FYSETC Voron V0_Display 1.3 inch OLED controller PCB with rotary encoder, reset/kill buttons, USB port, GPIO header, and onboard Neopixel

3D Printer Parts > Electronics > Displays

Voron v0 Display

Klicky Probe hardware kit with microswitch, 6x3 magnets, screws, threaded inserts and T-nuts for Voron magnetic Z probe

3D Printer Probe Kit

Klicky Probe Kit

TCRT5000 reflective optical sensor module on a small breakout PCB, top-down view: 4-pin header (Vcc, GND, DO, AO), IR LED + phototransistor package, sensitivity trimpot, two 3 mm mounting holes.

Reflective Optical Sensor

TCRT5000 Sensor

Molex 43045-1400 black Micro-Fit 3.0 14-circuit right-angle PCB header connector

3D Printer Parts > Electrical > Wire Connectors

Molex 43045-1400 Micro-Fit 3.0 14-Pin 14-Way Female Header Connector

Black Voron V0.1 umbilical frame and toolhead PCBs with JST-XH headers, 14-pin Micro-Fit connector, and blue screw terminal

3D Printer Parts > Electronics > Toolhead PCB

Voron v0 Umbillical and Rear Connector Boards Pack

Black and clear slim nylon zip ties for Voron cable management, 2mm wide, 40 pack

3D Printer Parts > Cable Management > Zip Ties

Voron Slim Zip-Tie Kit

Black nylon 4 inch and 12 inch zip ties for Voron cable routing and wiring cleanup

3D Printer Parts > Cable Management > Zip Ties

Voron Zip Tie Kit