Low Inventory

Sort by

▾

↑ Load previous

HT-NTC100K high-temperature 100K NTC thermistor probe with white lead and black 2-pin connector

3D Printer Parts > Electronics > Temperature Sensor

High Temperature Thermistor HT-NTC100K

GDSTIME GDB4010 4010 24V dual ball radial blower fan with 2-pin XH2.54 lead for 3D printer part cooling

4010 24v Dual Ball Blower Fan

GDSTIME GDB3010 24V 3010 radial blower fan front view with side outlet and red-black leads

3010 24v Dual Ball Blower Fan

Voron V0.1 belted Z kit hardware with GT2 belt, 20T pulleys, bearings, shaft, washers, nuts, inserts, and fasteners

3D Printer Parts > Motion Kits

Voron V0 Belted Z Kit

Molex 43045-1400 black Micro-Fit 3.0 14-circuit right-angle PCB header connector

3D Printer Parts > Electrical > Wire Connectors

Molex 43045-1400 Micro-Fit 3.0 14-Pin 14-Way Female Header Connector

XL6009E1 adjustable DC-DC boost converter module with inductor, trim potentiometer, and input/output pads

DC-DC Converter

XL6009E1 Step-Up Adjustable DC-DC Switching Boost Converter

Black Voron V0.1 umbilical frame and toolhead PCBs with JST-XH headers, 14-pin Micro-Fit connector, and blue screw terminal

3D Printer Parts > Electronics > Toolhead PCB

Voron v0 Umbillical and Rear Connector Boards Pack

Black and clear slim nylon zip ties for Voron cable management, 2mm wide, 40 pack

3D Printer Parts > Cable Management > Zip Ties

Voron Slim Zip-Tie Kit

Enraged Rabbit Carrot Patch ERCP hardware kit with fasteners, 608ZZ bearing, ECAS04 collet and PTFE fittings

3D Printer Parts > ERCF Hardware Kits

Enraged Rabbit Carrot Patch

Transparent FEP filament feed tube coil, 2.5 mm ID x 4 mm OD, for ERCF and Bowden-style filament paths

Transparent FEP Tube

Runice nickel-plated copper V6 nozzle for 1.75mm filament, available in 0.40, 0.60, and 0.80mm orifice sizes

3D Printer Nozzle

Plated Copper Nozzle by Runice

Black M12 spiral nylon cable glands with threaded compression fittings for IP68 strain relief

M12 Nylon Cable Gland

Deflanged GT2 20 tooth pulley and 5 mm x 30 mm steel pin for Voron 2.4 Z endstop

3D Printer Parts > Motion > Pulleys

Deflanged 20 Tooth with 30mm Pin for Voron 2.4 Z Endstop

BMG-style clone extruder gear set with hobbed drive gears, needle bearings, square nuts, and shaft

3D Printer Parts > Extruder Hardware

BMG Clone Extruder Gears

Pile of F623-2RS flanged miniature ball bearings with black rubber seals for 3mm shafts

F623-RS Bearings

~~$8.94~~

Two PC4-01 / PC4-M10 metal pneumatic Bowden fittings with black push collars for 4 mm PTFE or FEP tube

3D Printer Parts > Bowden Tube Couplers

PC4-01 / PC4-M10 Press Fit Pneumatic Fitting

5mm D-cut bearing steel shafts with ground flats in multiple short lengths for 3D printer pulleys and motion assemblies

3D Printer Parts > Motion > Shafts & Rods

5mm D-Cut Shaft — every length: Voron 2.4 Z, Micron Z, V0 Belted Z, LH Stinger, ERCF v1.1 / v2 / v3

Nickel-plated hammerhead T-nuts for 20-series 6 mm-slot aluminium extrusion, with M3 and M5 pack options.

Hammerhead T-Nuts for 20 Series Aluminium Extrusion

~~$8.98~~

3D Printer Build Plate

Spring Steel Sheet Double Sided Textured/Smooth PEI

Coiled genuine Gates LL-2GT 9mm RF open GT2 timing belt in black fiberglass-reinforced rubber

Gates LL-2GT 9mm RF Timing Belt — Clearance Cut Lengths